Pantograph or Moving Mast Reach Truck? A Guide for Western Australia Warehouses
Inside a new distribution centre in Hazelmere or Perth Airport’s logistics precinct, the racking climbs well past what any counterbalance forklift could reach, and the aisles are only just wide enough for the machine that serves them. That machine is a reach truck. When a warehouse manager starts shopping for one, the first choice is not brand or capacity. It is a format: pantograph or moving mast.
Both types perform the same basic job: placing pallets high in narrow aisles. They just do it in different ways, with the operator in a different position and a different rhythm to the shift. Getting that match right affects productivity, operator comfort and training more than most buyers expect.
At a glance
- A pantograph truck pushes its forks out on scissor arms. A moving mast truck slides the whole mast forward.
- Pantograph operators usually stand, which suits frequent stepping on and off. Moving mast operators usually sit, which suits long stints at the controls.
- Hyundai’s moving mast BRJ-9 series lifts up to 10.5 m or 12.0 m, depending on the capacity and mast configuration.
- Choose a shift pattern, operator experience and your actual aisles, not on format alone.
How each design reaches into the racking
Pantograph. The forks sit on a scissor linkage. While the truck travels, the linkage is folded back. At the rack face, it extends to push the forks forward and pull them back with the pallet, while the chassis stays where it is. The operator usually stands side-on, so they can look both ways along the aisle. Hyundai’s 15BRP-X is a stand-up pantograph model built for high-density storage.
Moving mast. Instead of the forks reaching out, the entire mast rolls forward along the chassis, over the base legs, to pick up or set down the load. It then retracts so the weight sits inside the wheelbase for travel. The operator normally sits side-on. This is the layout most Australian warehouse staff grew up with, and the Hyundai 16BRJ-9 is a typical example.
The two formats side by side
Both are electric, both straddle their baselegs for stability, and both are built for narrow aisles. The differences are in how they feel to work with.
| Pantograph | Moving mast | |
|---|---|---|
| How it reaches | Scissor linkage extends the forks | Whole mast slides forward |
| Operator stance | Standing, facing sideways | Seated, side-on |
| Best suited to | Frequent dismounts and picking | Long periods of pallet moving |
| Where it is common | North America | Europe and Australia |
| Hyundai example | 15BRP-X (1,500 kg) | 14, 16, 20 and 25BRJ-9 |
Either type, properly specified, will handle normal Australian racking. The deciding factors are the way your shifts run, what your operators are used to, and the aisles you have.
How high and how heavy
Reach trucks exist to lift higher than a counterbalance forklift can. Hyundai’s moving mast BRJ-9 range covers four capacities, all with a 14 km/h travel speed:
- 14BRJ-9: 1,400 kg, fork height up to 10.5 m
- 16BRJ-9: 1,600 kg, fork height up to 10.5 m
- 20BRJ-9: 2,000 kg, fork height up to 12.0 m
- 25BRJ-9: 2,500 kg, fork height up to 12.0 m
The 15BRP-X pantograph, at 1,500 kg, sits between the two smaller BRJ-9 models. Every BRJ-9 model can be ordered with three-stage, full-free-lift masts. Remember that the mast you choose sets two numbers at once: how high the forks go and how tall the truck is when lowered. In older Perth warehouses with low roller doors or mezzanines, the lowered height can rule out the tallest mast.
Safety features on each format
Both formats now come with curve control, which slows the truck through turns so it is not cornering too fast.
On the moving mast BRJ-9, you also get:
- An anti-rollback system that stops the truck from drifting backwards on a ramp.
- Automatic centring that straightens the drive wheel when the key is turned on.
- A steering angle display so the operator knows where the wheel is pointing.
- A down safety valve that holds the forks if a hydraulic line fails.
The 15BRP-X pantograph adds hill assist, and an optional pedestrian safety package with cameras, lights and audible warnings.
Three questions that settle the choice
- How often do operators get off the truck? If the job mixes driving with picking, scanning and checking on foot, a stand-up pantograph saves time on every climb on and off. If drivers spend hours moving pallets without leaving the seat, a sit-down moving mast is more comfortable.
- What are your drivers used to? Switching a crew to an unfamiliar format costs time while they adjust. If your team already knows one type well, there is value in staying with it. The 15BRP-X uses standard joystick controls, which keeps retraining short.
- What do your aisles and racks demand? Measure aisle width, top beam height, door clearances and pallet weights, then check them against the actual models on your shortlist rather than the format in general.
Batteries. The BRJ-9 range runs on a 48-volt system. The 15BRP-X uses 36 volts and can be ordered with a lithium battery. If you run one shift and charge overnight, the difference is small. If you run two or three shifts, lithium with opportunity charging during breaks is a real advantage, which currently tips things towards the pantograph.
What this means for Perth and WA sites
Many WA operations are moving into taller, denser buildings in Hazelmere, Kewdale, Jandakot and Bibra Lake, while others are making the most of older sheds with lower clearances. Cold stores for WA produce and grocery distribution often run around the clock, which puts battery strategy front and centre. A sit-down moving mast truck remains a safe default for long pallet-moving shifts. A stand-up pantograph deserves a look where operators are constantly on and off the truck.
HMH WA’s team can measure your aisles and racking, compare models, and help you decide between buying and short or long-term hire. You can also browse our warehouse equipment and talk to us about servicing and repairs once the truck is on the floor.
Related Hyundai equipment
Hyundai reach trucks
Warehouse equipment · View range
Hyundai order pickers
Warehouse equipment · View range
Warehouse equipment hire
Short and long term · View hire
Hyundai 25B-X
2.5 tonne lithium · View model
Frequently asked questions
What is the difference between a pantograph and a moving mast reach truck?
A pantograph truck extends its forks on a scissor linkage while the chassis stays put. A moving mast truck slides its whole mast forward to reach the load. Both work in narrow aisles. The main differences are how the operator stands or sits and the rhythm of the work.
Is a stand-up or sit-down reach truck better?
Neither is better in every case. Stand-up trucks suit jobs where operators get on and off often. Sit-down trucks suit long shifts spent moving pallets. Match the truck to your shift pattern and what your operators already know.
How high can a Hyundai reach truck lift?
The moving mast BRJ-9 range reaches up to 10.5 m on the 14BRJ-9 and 16BRJ-9, and up to 12.0 m on the 20BRJ-9 and 25BRJ-9, depending on the mast fitted. A taller mast also raises the lowered height, so check door clearances.
Talk to our Team
Sales, Hire, Servicing and Genuine Parts from Hyundai Material Handling WA.
Latest Posts
Recent Posts
Why Buy From Hyundai Material Handling WA
Buying a forklift is a long-term decision. With a local Hyundai dealer, you get sales, service, parts and hire from one Perth-based team.
Perth Based Team
Talk to people who know Western Australian sites, from our base in Bassendean.
Servicing and Repairs
Scheduled servicing and repairs by Hyundai-trained technicians.
Genuine Hyundai Parts
Genuine parts sourced through our Perth parts team.
Buy or Hire
Purchase outright or ask about short and long term hire options.
Get a Brochure and a Quote
Download a brochure, or tell us about your loads, lift heights and site and we will recommend the right Hyundai forklift. We supply businesses across Perth and regional Western Australia.
Fill out the form below, and we will contact you as soon as possible.
Contact or call us directly on (08) 9377 3321
Customer Reviews
Hundreds of Western Australian Businesses Trust Hyundai Material Handling.
See our 5-star reviews and long-standing client partnerships.
Our clients choose us for reliability, honesty, and expert forklift support.
Ready to Talk Forklifts?
Speak with our Perth team about pricing, availability, hire and finance.